Pay in installments of $63.38 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 31 - Aug 5
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
CUAV X7+ Standard Autopilot Flight Controller - PX4/APMThe X7+ Standard Autopilot Flight Controller is a high performance autopilot. It is an ideal choice for industrial drones and large scale heavy duty drones. The X7+ features an H7 processor, an upgraded sensor with a redundancy design, a temperature compensation system, and a CORE separate design. The X7+ adopts a modular design and can be matched with different base plates. You can design a dedicated carrier board for your UAV to improve the
The X7+® Standard Autopilot Flight Controller is a high-performance autopilot. It is an ideal choice for industrial drones and large-scale heavy-duty drones. The X7+ features an H7 processor, an upgraded sensor with a redundancy design, a temperature compensation system, and a CORE separate design. The X7+ adopts a modular design and can be matched with different base plates. You can design a dedicated carrier board for your UAV to improve the integration of commercial systems, reduce wiring, improve system reliability, and enhance your UAV competitiveness (for example, by integrating airspeed sensors, telemetry, or even a companion computer, in the carrier board).
VIDEO: CUAV client X7 Flight Control Vertical Take-off and Landing Aircraft
Features
- Supports USB_HS, downloads logs faster (PX4 not yet supported)
- Supports IMU heating, making the sensor work better
- Modular design can be DIY carrier board
- Supports temperature compensation
- Dedicated uavcan battery port
- Supports more DSHOT output
- Car-grade RM3100 compass
- High-performance processor
- Internal shock absorption
- Internal shock absorption
- 3 sets of IMU sensors
- Three imus
OVER-CURRENT PROTECTION
The X7+ has over-current protection on the 5 Volt Peripheral and 5 Volt high power, which limits the current to 2.5A. The X7 has short circuit protection. Up to 2.5 A can be delivered to the connectors listed as pin 1 (although these are only rated at 1 A).
BUILDING FIRMWARE
The system's serial console and SWD interface operate on the DSU7 port. Simply connect the FTDI cable to the DSU7 connector (the product list contains the CUAV FTDI cable). CUAV provides a dedicated debugging cable, which can be connected to the DSU7 port. This splits out an FTDI cable for connecting the PX4 System Console to a computer USB port, and SWD pins used for SWD/JTAG debugging. The provided debug cable does not connect to the SWD port Vref pin (1).
TRIPLE REDUNDANT
The X7+ AutoPilot can be triple-redundant on the power supply if three power sources are supplied. The power rails are POWERA, POWERC, and USB. The output power rails PWM OUT (0V to 36V) do not power the flight controller board (and are not powered by it). You must supply power to one of POWERA, POWERC, or USB or the board will be unpowered.
DEBUG PORT
The system's serial console and SWD interface operate on the DSU7 port. Simply connect the FTDI cable to the DSU7 connector (the product list contains the CUAV FTDI cable). CUAV provides a dedicated debugging cable, which can be connected to the DSU7 port. This splits out an FTDI cable for connecting the PX4 System Console to a computer USB port, and SWD pins used for SWD/JTAG debugging. The provided debug cable does not connect to the SWD port Vref pin (1).
Specifications
- Interfaces:
- 2 Power ports(Power A is common adc interface, Power C is uavcan battery interface)
- Support multiple RC inputs (SBUs / CPPM / DSM)
- 14 PWM outputs （12 supports Dshot）
- 4 i2c buses(Two i2c dedicated ports)
- 2 GPS ports(GPS and UART4 ports)
- Analogue / PWM RSSI input
- 2 CAN bus ports
- 2 ADC input
- 1 USB ports
- On-board sensors:
- Accelerometer/Gyroscope: ICM-20689
- Accelerometer/Gyroscope: ICM-20649
- Accelerometer/Gyroscope: BMI088
- Magnetometer: RM3100
- Barometer: MS5611*2
- Operating temperature: -20 ~ 80°c
- Main FMU Processor: STM32H743
- Power System:
- Servo Rail Input: 0~36V
- USB Input: 4.75~5.25V
- Power: 4.3~5.4V
- Weight: 101 g
IMPORTANT NOTES
- When it runs PX4 firmware, only 8 PWM works, the remaining 6 PWM are still being adapted, so it is not compatible with VOLT now.
Includes
- 1x CUAV X7+ Standard Autopilot Flight Controller (for PX4/APM)
- 1x CAN PMU Lite Power Module
- 1z CAN Extension Board
- 1x 16G Memory Card
- 1x 12C / CAN Cable
- 1x Pw-Link Module
- 1x ADC3.23 Cable
- 1x USB-C Cable
- 1x RSSI Cable
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy