Pay in installments of $23.46 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 27 - Aug 1
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
XCMD2110L2Main Range of product OsiSense XC Series name Standard format Product or component type Limit switch Device short name XCMD Sensor design Miniature Body type Fixed Head type Plunger head Material Metal Body material Zamak Head material Zamak Fixing mode By the body Movement of operating head Linear Type of operator Spring return plunger metal Type of approach Vertical approach, 1 direction Number of poles 2 Contacts type and composition 1 NC + 1 NO
Main
| Range of product | OsiSense XC |
| Series name | Standard format |
| Product or component type | Limit switch |
| Device short name | XCMD |
| Sensor design | Miniature |
| Body type | Fixed |
| Head type | Plunger head |
| Material | Metal |
| Body material | Zamak |
| Head material | Zamak |
| Fixing mode | By the body |
| Movement of operating head | Linear |
| Type of operator | Spring return plunger metal |
| Type of approach | Vertical approach, 1 direction |
| Number of poles | 2 |
| Contacts type and composition | 1 NC + 1 NO |
| Contact operation | Snap action |
Complementary
| Switch actuation | On end |
| Electrical connection | Removable cable connector |
| Cable length | 2 m |
| Cable composition | 5 x 0.75 mm² |
| Wire insulation material | PvR |
| Contacts insulation form | Zb |
| Positive opening | With |
| Positive opening minimum force | 42.5 N |
| Minimum force for tripping | 8.5 N |
| Minimum actuation speed | 0.01 m/min |
| Maximum actuation speed | 0.5 m/s |
| Contact code designation | B300, AC-15 (Ue = 240 V), Ie = 1.5 A conforming to EN/IEC 60947-5-1 appendix A R300, DC-13 (Ue = 250 V), Ie = 0.1 A conforming to EN/IEC 60947-5-1 appendix A |
| [Ui] rated insulation voltage | 300 V (pollution degree 3) conforming to UL 508 400 V (pollution degree 3) conforming to IEC 60947-5-1 300 V (pollution degree 3) conforming to CSA C22.2 No 14 |
| [Uimp] rated impulse withstand voltage | 4 kV IEC 60664 4 kV IEC 60947-1 |
| Short-circuit protection | 6 A cartridge fuse, type gG |
| Electrical durability | 5000000 cycles, DC-13, 120 V, 1 W, operating rate <60 cyc/mn, load factor: 0.5 conforming to IEC 60947-5-1 appendix C 5000000 cycles, DC-13, 24 V, 3 W, operating rate <60 cyc/mn, load factor: 0.5 conforming to IEC 60947-5-1 appendix C 5000000 cycles, DC-13, 48 V, 2 W, operating rate <60 cyc/mn, load factor: 0.5 conforming to IEC 60947-5-1 appendix C |
| Mechanical durability | 10000000 cycles |
| Width | 30 mm |
| Height | 50 mm |
| Depth | 16 mm |
Environment
| Shock resistance | 25 gn for 18 ms conforming to IEC 60068-2-27 |
| Vibration resistance | 5 gn (f= 10…500 Hz) conforming to IEC 60068-2-6 |
| IP degree of protection | IP66 conforming to IEC 60529 IP67 conforming to IEC 60529 IP68 conforming to IEC 60529 |
| IK degree of protection | IK06 conforming to EN 62262 |
| Overvoltage category | Class I |
| Ambient air temperature for operation | -25…70 °C |
| Product certifications | UL CSA |
| Standards | EN 60947-5-1 CSA C22.2 No 14 UL 508 IEC 60947-5-1 |
Offer Sustainability
| Sustainable offer status | Green Premium product |
| REACh Regulation | REACh Declaration |
| EU RoHS Directive | Pro-active compliance (Product out of EU RoHS legal scope) EU RoHS Declaration |
| Mercury free | Yes |
| RoHS exemption information | Yes |
| Environmental Disclosure | Product Environmental Profile |
| Circularity Profile | End of Life Information |
Contractual warranty
| Warranty | 18 months |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.2 ★★★★★
Based on 16 reviews
Sort
Product Reviews
★★★★★ 5
Superior Design!
Size: 6 Pairs / 12 pcs
Delivery was lightning fast.
I tried a pack of two pairs of these banana jacks as a sample to see if these would meet my needs. The design of these plugs is superior. The design was exactly what I wanted because the speaker wire is secured with TWO set screws. Then I ordered an additional six pairs of plugs to hook up my subwoofer to my amp and speakers.
(I feed the audio output from the amp to the sub. The sub has a crossover that keeps the low frequencies and sends the mid and treble frequencies to my bookshelf speakers.)
I love the security of two set screws on each plug and love the barrel that screws on AFTER the wire is secured by the set screws. Most banana plugs have a hole through the shaft of the plug that receives the stripped wire. Then the barrel cover is screwed down to secure the wire in the plug. This design compresses the speaker wire but eventually the cap loses it grip and allows the connection between the wire and the plug to become loose. Then the transfer of the audio signal becomes poor and the speakers sound bad. Every month or two I needed to check all the banana plugs and re-tighten many of them for the best performance. The two set screws eliminate this problem. The set screws are quite small and take a little extra care in installation. You will need a small flat blade screwdriver to tighten them. I used the 1/8" flat blade driver from a set of jewelers screwdrivers.
These well made plugs are a bit pricier that many of the banana plugs available but certainly not the priciest plugs available. For me, the slightly higher price was more than offset by the security of the wire within the plug.
I'm not thrilled with the extra tight fit of the tip on the plugs into the jacks. It took a lot of effort to insert the in the jack. Actually I "greased" the pins (very sparingly) with with non-corrosion, conductive paste (Ox-Gard, No-Corrode, etc. Do NOT use any other grease.) Next time I'll use pliers to compress the pin.
My only quibbles are that the spring pins that go into the jack are very tight and that the plugs are only sold in quantities of two pairs or 12 pairs.
I recommend these banana plugs for all who are using the banana plugs and jacks for hooking up your speakers. It's a very convenient way of connecting speakers if your speakers and amplifier have the banana jack as part of the binding post. Further, it's much safer to use banana plugs since the possibility of shorting your amplifier with a stray strand of wire is practically zero. Easy Five Stars.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 13, 2018
★★★★★ 5
Top banana
Size: 5 Pairs / 10 pcs
Theses banana plugs are hight quality non magnetic. Banana plugs easy to usexand very high quality sound different because of the better connection and quality.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 24, 2026
★★★★★ 5
Very easy to use
Size: 12 Pairs / 24 pcs
I have an Onkyo audio/video receiver along with an Emotiva amplifier. Both have speaker "post" terminals which will accept banana plugs, OR I can connect the speaker wires by unscrewing the posts, poke the speaker wires into the terminals and then tighten the posts. The problem with poking the wires into the terminals and tightening the posts vs using banana plugs is that there is a risk of the wires touching the metal on the back of the chassis or touching other speaker wires, causing a short if one is not careful. With banana plugs, they simply plug into the back/top of the posts, eliminating the rsick of a short circuit. They can also be unplugged very easily if needed. Banana plugs are DEFINITELY the preferred way to connect speakers to an receiver or amplifier if they have post-style terminals.
These particular banana plugs came in a package of 12 I believe. They were very reasonably priced, and simple to connect to the end of the speaker wires. Simply unscrew the banana plugs, use a small, standard jewelry screwdriver and loosen both of the set screws, insert the speaker wire, then tighten the set screws, and then screw the banana plug back together.
The plugs have either a red band which would typically be used for your "Right" speakers, or a black band which would typically be used for the "left" speakers. The banana plugs insert into the top or front of the speaker terminal posts on the amp and receiver. They fit VERY snug, and so I did have to apply just a little bit of pressure in order to insert them into the posts, but once plugged in, rest assured they're not going anywhere. They are snug.
I highly recommend these.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 2, 2025
★★★★★ 5
Great wire, great price
Size: 100-Foot, Style: 14-Gauge
There is something about this wire that makes me buy it again and again, and makes me feel like it’s a great value! it’s pure copper strands and it feels, looks solid and as good as anything I ever bought for the sound transmission
The cover is thick, but the wire is still flexible. Looks professional and the white looks better than the old school copper look. Getting the protective sleeve off is a bit of challenge but for me it’s worth it. Have a utility knife, wire strippers and if you have weaker hands, a pair of pliers or something to grip it with to remove from covering wires. It’s worth the effort to me as the results feel solid
I use this with my higher end vintage M&K, Sansui, Pioneer, Timeframe, and other amps, speakers and to my ears, it delivers simple, clean sound at a great price. Don’t buy the hype, buy good wire and call it a day. This 14 gauge even works well with clip posts like on my Sansui 9090DB. 👌
Only thing I would do different, buy the 200ft if you are hooking up Atmos or have multiple equipment. This is my third 100ft in as many months, Lol
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 18, 2023
★★★★★ 5
Perfect and easy to splice buy durable.
Size: 100-Foot, Style: 14-Gauge
Used for home audio setup. Klipsch speakers to Denon receiver. Could've wired directly but chose to add the plug ins for connecting. Sound quality is amazing. Perfect gauge and high quality strands. Easy to work with amd splice when needed.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 24, 2026
recommand products
Roc N Soc Manual Spindle Black Saddle Throne Short MSS O-K
156.00
Tama Bass Drum Spurs Pair MSPRSC2P
78.99
Westbury 3 PC Junior Drum Kit w/ Hardware, Cymbals & Throne - Prismatic Finish
110.00
Remo 22" Powerstroke 3 Coated Black Dot Bass Drum Head - Bottom Black Dot
85.99
"Contes D'Hoffmann Vol. I- IV" 1956 BEGUIN, Albert
300.00